posted
are going on tomorrow. Leaving the loudmouth on for now, so it may be just a little bit louder.
Once I can retune it and get to the dyno, I'll know how much of an increase I get from them.
Then it will be time to plan the heads and cam install.
--------------------
Kevin Villier, 2002 SS #186 - 6M with Hurst and "short-stick", TT, navy blue, chrome SS wheels, Bilstein suspension, SS grill, BMR STB, BMR chrome-moly panhard rod, SLP loudmouth, Direct-Flo lid with Holley Power Shot filter, mallory polished MAF ends, 4.10 gears, PPC LT's. 336 rwhp, 345 rwtq
posted
Oh man. Flamingbird just got her long tubes installed with the loudmouth. Holy crap is that thing loud. You can hear her coming about a mile away, literally
Posts: 1031 | From: Germantown, MD USA | Registered: Feb 2000
| IP: Logged
posted
Hawkeye, got your message, post here if you can. I got in late from the "attemp" at getting everything in. We are going to try and finish up today if the weather cooperates.
I have to get a tap and tap out the O2 bungs on the Y-pipe to be able to get the O2 sensors in. The polishing material is apparently in the threads and the sensors won't go in.
I'm still trying to figure out how I'm going to be able to get the I-pipe portion of the loudmouth connected to the reducer pipe.
I couldn't believe we had to remove the oil filter, oil drain plug, unbolt the tranny, drop it down a few inches and shove it over as far as we could and still almost had to grind the lip off the K member to be able to get the drivers side header in. We had a bunch of experienced header install folks there and they couldn't believe how much trouble it was to get it in and have to tap the O2 bungs and figure out now how to get the LM hooked up still.
Hopefully, I will be able to get it finished today and able to drive it home.
Wish me luck. All I can say it better show it on the dyno that it was worth it.
Posts: 763 | From: Louisville, KY | Registered: Jun 2001
| IP: Logged
I'm searching a piece of pipe this morning to connect my Borla Int. pipe to the reducer.
I did not move the tranny - although I thought of it! The key was in the way it was lifted.
I had a stipped bolt hole in the block! That was a fun fix. Then last night I broke a bolt on a clamp tightening it up. The front CAT bolt no less.
No problem with the 02 sensors, other than when I took one out it was stripped. So, I bought a new one.
Are you putting the tunnel brace back on? I'm buying longer bolts for that this morning and some spacers.
Having fun yet? I hope the dyno shows!
-------------------- Hawkeye: SSOA F98-C98
1998 SS - Black All Options - Mods Whisper Lid, K & N, Lou's Short Stick, Shift Light, Skip Shift, SLP Y, Borla, 4:10's, BMR STB, SLP SFCs, Granatelli MAF, Hypertech III, 160 Stat, Mallory Billet Pedals, Metco Aluminum LCAs,Fast Toys Ram Air Mod, Spohn Panhard Bar, BMR Torque Arm, free EGR mod,power antenna, BMR LCA brackets, Gentex Temp/Compass Auto Dim Mirror, AllMaxx Strobe and Wig Wag, BAER Eradispeed rotors,PPC Headers with Random Technology Hi Flow Cats, BMR Drive shaft Loop,FAST 78MM Throttle Body, FAST 78MM Composite Intake, Mobil 1 & lots of Zaino.
Wife & Best Friend Mary - copilot. Posts: 5558 | From: Windsor, Ontario. Canada | Registered: Feb 2000
| IP: Logged
posted
I finished mine last and then left the country for 7 days. It is certainly louder with the new cats/y-pipe and stock muffler. I can't say I can really tell a SOTP difference though. Hopefully off to the dyno next week for the data.
posted
Got mine all done yesterday. Had to modify the reducer and loudmouth pipes alot to make it fit together. The dyno and track should give me what the gains are.
Definitely louder and I kept the loudmouth on. It has a great deep tone to it, but probably too loud for the boys in blue. If I get pulled over for it, I guess I'll have to go with a muffler cat-back and an electric cutout.
--------------------
Kevin Villier, 2002 SS #186 - 6M with Hurst and "short-stick", TT, navy blue, chrome SS wheels, Bilstein suspension, SS grill, BMR STB, BMR chrome-moly panhard rod, SLP loudmouth, Direct-Flo lid with Holley Power Shot filter, mallory polished MAF ends, 4.10 gears, PPC LT's. 336 rwhp, 345 rwtq
posted
Mine is on with the exception of a 6" custom pipe I'll need in order to mate the reducer up with my Borla system. I'll be getting that fabbed tomorrow. All in all I was fairly impressed with the fit. The drivers side s-pipe to cat to y-pipe alignment was a little tricky but once I got that right I was able to work the passenger side stuff into place.
How is everybody's ground clearance looking on the driver's side at the cat?
quote:Originally posted by Doug 97SS #1499: Oh man. Flamingbird just got her long tubes installed with the loudmouth. Holy crap is that thing loud. You can hear her coming about a mile away, literally
Doug...take the "G" outta mine name . Yeah I guess my car is quite loud! Tee hee!!
Here's the mpg of it for those that might've missed it
quote:Originally posted by John01SS: Mine is on with the exception of a 6" custom pipe I'll need in order to mate the reducer up with my Borla system. I'll be getting that fabbed tomorrow. All in all I was fairly impressed with the fit. The drivers side s-pipe to cat to y-pipe alignment was a little tricky but once I got that right I was able to work the passenger side stuff into place.
How is everybody's ground clearance looking on the driver's side at the cat?
Man, I can't wait to fire the car up tomorrow!
- John
The drivers side cat is the low point of the system, but not much lower than the SFCs. I have a small leak at the S pipe clamp. My plan is to have that joint welded. I also want to have a new piece made to join the borla. I made up a joint with a 3" to 3" adapter piece. That fit into the Intermediate Borla pipe I cut down to to 1 and 1/2" from the joint. So now there are 4 clamps in about and 18" span. I want that all in one piece welded in. It sounds much louder now than before. It's still up on ramps because I have to re fit the tunnel brace with some spacers and longer bolts.
-------------------- Hawkeye: SSOA F98-C98
1998 SS - Black All Options - Mods Whisper Lid, K & N, Lou's Short Stick, Shift Light, Skip Shift, SLP Y, Borla, 4:10's, BMR STB, SLP SFCs, Granatelli MAF, Hypertech III, 160 Stat, Mallory Billet Pedals, Metco Aluminum LCAs,Fast Toys Ram Air Mod, Spohn Panhard Bar, BMR Torque Arm, free EGR mod,power antenna, BMR LCA brackets, Gentex Temp/Compass Auto Dim Mirror, AllMaxx Strobe and Wig Wag, BAER Eradispeed rotors,PPC Headers with Random Technology Hi Flow Cats, BMR Drive shaft Loop,FAST 78MM Throttle Body, FAST 78MM Composite Intake, Mobil 1 & lots of Zaino.
Wife & Best Friend Mary - copilot. Posts: 5558 | From: Windsor, Ontario. Canada | Registered: Feb 2000
| IP: Logged
I thought about 1 - but I have a BMR Torque Arm, don't know if it will work. I could check with BMR.
-------------------- Hawkeye: SSOA F98-C98
1998 SS - Black All Options - Mods Whisper Lid, K & N, Lou's Short Stick, Shift Light, Skip Shift, SLP Y, Borla, 4:10's, BMR STB, SLP SFCs, Granatelli MAF, Hypertech III, 160 Stat, Mallory Billet Pedals, Metco Aluminum LCAs,Fast Toys Ram Air Mod, Spohn Panhard Bar, BMR Torque Arm, free EGR mod,power antenna, BMR LCA brackets, Gentex Temp/Compass Auto Dim Mirror, AllMaxx Strobe and Wig Wag, BAER Eradispeed rotors,PPC Headers with Random Technology Hi Flow Cats, BMR Drive shaft Loop,FAST 78MM Throttle Body, FAST 78MM Composite Intake, Mobil 1 & lots of Zaino.
Wife & Best Friend Mary - copilot. Posts: 5558 | From: Windsor, Ontario. Canada | Registered: Feb 2000
| IP: Logged
posted
I'm also likely to go with the BMR, but for now I just left the stock one off. Maybe spacers should come with the header kit since the tunnel brace will NOT go on with the PPC system without spacers. Now if I can find some kind of spacers that will look OK and not have to just put alot of washers together.
--------------------
Kevin Villier, 2002 SS #186 - 6M with Hurst and "short-stick", TT, navy blue, chrome SS wheels, Bilstein suspension, SS grill, BMR STB, BMR chrome-moly panhard rod, SLP loudmouth, Direct-Flo lid with Holley Power Shot filter, mallory polished MAF ends, 4.10 gears, PPC LT's. 336 rwhp, 345 rwtq
Printer-friendly view of this topic
![[Roll Eyes]](rolleyes.gif)
![[Big Grin]](biggrin.gif)
![[Eek!]](eek.gif)
![[Smile]](smile.gif)
![[Mad]](mad.gif)
![[Wink]](wink.gif)
. Yeah I guess my car is quite loud! Tee hee!!
